Home > Mold Removal > Mold Remediation FAQs > Uses for MoldSTAT Plus

What are some uses of MoldStat Plus ?

MoldSTAT Plus in WATER/SMOKE DAMAGE RESTORATION

Effective against odor causing bacteria and fungi for home, institutional, industrial and hospital use. This product is particularly suitable for use in water damage restoration situations against odor causing bacteria on the following porous and semi-porous materials: carpets, carpet cushion, sub floors, drywall, trim, frame lumber, tackless strip and paneling. Using solutions recommended, saturate affected materials with enough MoldSTAT Plus to remain wet for at least 10 minutes. Use proper ventilation.

MoldSTAT Plus in Sewer Backup and River Flooding:

During mitigation procedures, dilute 1/2 to 1 ounce of MoldSTAT Plus per gallon of water. (Always follow MoldStat Plus Directions for use contained in fold out instructions on back of bottle). When diluting moldstat plus, always allowi for the diluting effect of absorbed water already present within saturated materials.
Remove gross filth or heavy soil along with non-salvageable materials. Saturate all affected areas with a sprayer using a coarse spray tip, before and after cleaning and extraction.

Carpets, carpet cushions and other porous materials such as sub floors, drywall, trim and frame timber, tackless strip and paneling

For water damage from a clean water source, extract excess water. Test hidden area for colorfastness. Dilute 1/2 to 1 ounce of the MoldSTAT Plus per gallon of water, allowing for the diluting effect of the absorbed water within saturated materials. Remove gross filth or heavy soil. Apply directly with a sprayer using a coarse spray tip, to fully saturate affected materials. Roll, brush, or agitate into materials and allow the materials to remain damp for 10 minutes. Follow with a thorough extraction. Dry rapidly and thoroughly.

MoldSTAT Plus for Cleaning Carpet Against Odor Causing Bacteria

MoldSTAT Plus may be used in industrial and institutional areas such as homes, motel and hotel chains, nursing homes, schools and hospitals. For use on wet, cleanable synthetic fibers. Do not use on wool. Vacuum carpet thoroughly prior to cleaning. Test fabric for color fastness. Over-wetting can cause carpet to shrink. Manufacturer assumes no responsibility for over-wetting misuse.

MoldSTAT Plus For portable extraction units:

Mix 1/2 ounce of this product per gallon of water. Do not mix this product with other cleaning products. Follow the cleaning procedures specified by the manufacturer of the cleaning equipment. After using this product, set the carpet pile and protect the carpet from furniture legs and bases while drying. Do no over wet. If applied to stain resistant nylon carpet, apply a fabric protector according to the carpet manufacturer directions.

MoldSTAT Plus in Smoke Damage Restoration:

Effective against odor causing bacteria and fungi for home, institutional, industrial and hospital use. This product is particularly suitable for use in smoke damage restoration situations against odor causing bacteria on porous and semi-porous materials: carpets, carpet cushion, sub floors, drywall, trim, frame lumber, tackless strip and paneling. Follow directions as outlined in the Water Damage Restoration section. Using solutions recommended, saturate affected materials with enough product to remain wet for at least 10 minutes. Use proper ventilation.

MoldSTAT Plus For Schools, Industry and Non-Medical Institutional Uses:

At 1/2 ounce per gallon of water, this product delivers cleaning and germicidal effectiveness. Treated surfaces must remain wet for 10 minutes, then allow to air dry or wipe. For heavily soiled areas, a preliminary cleaning is required. Prepare a fresh solution at least daily or more often if solution becomes diluted or soiled. It is effective against Staphylococcus aureus, Salmonella cholerasuis, Escherichia coli and Serratia marcescens. The same AOAC tests used to confirm performance for hospitals were used.

Fungicidal Use Dilution Chart

Ounces of Product

Amount of Water

3/8 ounce

1/2 gallon

1/2 ounce

1 gallon

1 1/2 ounces

2 gallons

Sort By:
1
MoldSTAT Plus Mold Killer | Makes 21 gallons MoldSTAT HVAC - Air Vent Mold Remover Mold Killer Kit (45% Off)
Cleaner Today: $44.99
Mold Killer Savings: $28.75
Cleaner Today: $51.25
Mold Remover Sale: $36.75
Cleaner Today: $93.67
Mold Remover Sale: $51.75
Free Delivery Included
MoldSTAT Plus Mold Killer MOLDSTAT HVAC - The Effective Mold Odor Control Mold KIller Kit - MoldSTAT peroxy , Plus & Aireze
MoldSTAT Plus Mold Killer
EPA registered Mold Killing solution
Non Bleach mold remover
Makes 21 gallons
HVAC Mold Remover yields 16 gallons
Controls and inhibits odors
Use for HVAC ductwork cleaning programs.
Mold Killer / Cleaner Kit
MoldSTAT Peroxy Kling - Mold cleaner
MoldSTAT Plus Mold Killer
2 Aireze - Airborne Mold Odor Remover
Mold Prevention Kit (45% Off)
Cleaner Today: $104.67
Mold Prevention Sale: $53.65
Free Delivery Included
Mold Prevention Kit
Mold Remediation & Prevention Kit
Clean and Kill Mold - MoldSTAT Plus
MoldSTAT Barrier - Mold prevention spray
2 Aireze - Airborne Mold Odor Remover
   
 
1